The Part Nobody Makes
Anymore? We Make It.
We manufacture hard-to-source industrial rubber products: obsolete equipment components, discontinued OEM parts, and specs that never appeared in any catalog. If you can put the part in a box, or photograph where it goes, we can usually make it. No drawing required.
Every Hard-to-Find Part Has a Reason
However your hard-to-source industrial rubber product came to be, none of these reasons change the fact that your equipment still needs to run.
01
The OEM Stopped Making It
The machine outlived its manufacturer. The parts catalog is gone, the drawings are gone, but your equipment still runs and still needs that seal.
02
No Drawing Exists
Legacy equipment, imported machinery, modified systems: the part exists only in the machine itself. Suppliers keep asking for a drawing nobody has.
03
The Spec Is Unusual
Non-standard profile, odd hardness, specialty compound, one-off dimension. It's not in any catalog because it was never a catalog part. It was made for your application.
Sourcing Problem Becomes Manufacturing Solution
You can't buy the part because nobody stocks it. So we make it once, correctly, and keep the spec on file for reorder.
Reverse-Engineering
Send us the part, working, worn, or broken. We measure geometry, test hardness, analyze the compound, and recreate it as a production-ready component.
Small-Batch Recreation
We don't need a production run to justify making your part. One replacement or ten: the batch size fits your maintenance schedule, not a factory minimum.
Compound Matching
A part is only a match if the rubber survives the same conditions. We identify and formulate for the original's temperature, chemical, and load profile.
Improved Redesign
If the original failed for a known reason, we can fix it (better compound, adjusted geometry, reinforced bonding) so the replacement outlasts the original.
From Mystery Part to Permanent Supply
The best part of recreating a part: once we hold the spec, it's never hard to source again. Your obsolete component becomes a reorderable line item with a file, a compound, and a tool.
- 1
Send What You Have
The physical part if possible, in any condition. Photos and measurements if shipping it first isn't practical. We'll tell you what we need.
- 2
Analysis & Quote
We measure, test, and identify the compound, then quote the recreation, including what we can improve and what must stay identical.
- 3
Sample Approval
You approve a production sample before the batch runs. For critical fits, we refine until it's right.
- 4
Production & Repeat Supply
Your part is produced and shipped, and because we now hold the spec, reordering is a phone call. The part is never hard to source again.
Hard-to-Source, Answered
Can you really make a part with no drawing and no part number?
Yes. The physical part is the drawing. We reverse-engineer geometry from the sample, test its hardness, and identify a matching compound, including from worn or broken parts where we reconstruct the intended profile. This is routine work for us, not an exception.
What if the part is damaged or incomplete?
Often still workable. Symmetric parts can be mirrored from the intact side; wear patterns and mating surfaces tell us the original profile; and context matters: if we can see where the part sits, we know what it has to seal, cushion, or isolate. We'll tell you honestly if a sample is too far gone and what would make it workable.
What kinds of parts do you recreate most often?
Seals and gaskets for legacy machinery, obsolete equipment components, custom profiles for imported machines with no local support, discontinued OEM parts, and unusual one-off specifications that catalog suppliers won't quote.
Is a recreated part as good as the original?
It's made on the same presses, in the same compounds, to the measured geometry of the original, and in many cases better, because we can correct the failure mode that retired the original part in the first place.
Can I order just one?
Yes. Replacement quantities match your need: a single emergency replacement or a small maintenance stock. See our low MOQ manufacturing page for how we handle small orders.
That Part You Can't Find? Box It Up.
Send us the part, or photos of it and where it sits. We'll tell you plainly whether we can recreate it, what it takes, and what it costs.
- No drawing needed
- Works from worn or broken samples
- Single pieces and small batches
- Spec kept on file for reorders